T
tineistwood
Nouveau
Bonjour a tous,
voila notre probleme, nous avons une decolleteuse star ecas 32t, nous realisons frequemment des tourbillonage pour des vis de longueur 25,30,40,50,60 sur des diametres de 6.5, avec comme contraintes, pas de 2.8 profondeur de fond de filet 3.6 , mais nous devons faire des vis de longueur 100 et la rien ne vas plus.
alors si vous connaisez bien le principe du tourbillonage nous sommes preneurs!!!
voici le programme
N10 CH3
N20 R2=3.65;DIAMETRE DEPART TOURBILLONNAGE Z0
N30 R3=0.45;ANGLE DE FILETAGE AU RAYON
N40 R4=95;LONGUEUR FILETAGE
N50 G0
N60 G28 X250.
N70 G28 Z0 Y0
N80 WAITM(1,1,3)
N90 TOP:
N100 G97
N110 G40 G95
N120 WCS140
N130 G28 X250.
N140 WAITM(2,1,2,3)
N150 MSG
N160 M20
N170 MSG("TOURNAGE 19.MM")
N180 T3131
N190 G0 X100.
N200 M133;1
N210 M203
N220 MS1
N230 G95G0X13.Z0M3S2500
N240 G1X-1.F0.03
N250 G1Z-1.F0.5
N260 G1G41Z-0.1X-0.1
N270 G1X0Z0F0.02
N280 G2 X1.732 Z.5 CR=1.
N290 G1X6.55 ANG=30.;3.7631
N300 G1Z19.F.02
N310 G1X11.6Z=IC(2.)
N320 G1X12.1Z=IC(0.25)F.02
N330 G0G40X13.Z=IC(1.)
N340 G0M213
N350 G28X250.M5
N360 MSG("")
N370 M1
N380 M131;2
N390 MSG("TOURBI.16MM ")
N400 T3900
N410 MS13
N420 M4S1800
N430 SPOS[1]=0
N440 waitm(10,1,3)
N450 G0Z-30. M203
N460 WCS141
N470 G0G94Z-4.
N480 G0 X=R2
N490 G1Z0F500
N500 G1 X=(R2+(18.*TAN(R3))*2) Z18. C1=(18./2.8)*360 F35
N510 G1X7.5 F1000
N520 G0Z-4.
N530 G0X100.
N540 M131;FRAISAGE
N550 G28X250.M5
N560 WCS140
N570 G28 Z0 M213
N580 MSG("")
N590 M1
N760 MSG("EBAVURAGE TOURBI. 16MM")
N770 T3900
N810 waitm(19,1,3)
N780 MS13
N790 M4S1800
N800 SPOS[1]=0
N820 G0Z-34. M203
N830 WCS141
N840 G0G94Z-4.
N850 G0 X=R2
N860 G1Z0F500
N500 G1 X=(R2+(11.*TAN(R3))*2) Z11. C1=(11./2.8)*360 F35
N500 G1 X=(R2+(18.*TAN(R3))*2) Z18.1 C1=(18./2.8)*360 F35
N890 G1 X7.5 F1000
N930 G0Z-4.
N940 G28X250.M5
N950 WCS140
N960 G28 Z0 M213
N970 MSG("")
N980 M1
N610 MSG("TOURNAGE 38.MM")
N620 T3131
G0X150.
N600 M133;3
N630 M203
N640 MS1
N650 G95G0X13.Z16.5M3S2500
N660 G1G41X6.55Z17.5F0.2
N670 G1Z38.F0.02
N680 G1X11.6Z=IC(2.)
N690 G1X12.1Z=IC(0.25)F.02
N700 G0G40X13.Z=IC(1.)
N710 G0M213
N720 G28X250.M5
N730 MSG("")
N740 M1
N750 M131;4
N760 MSG("TOURBI. 33MM")
N770 T3900
N780 MS13
N790 M4S1800
N800 SPOS[1]=0
N810 waitm(12,1,3)
N820 G0Z-34. M203
N830 WCS141
N840 G0G94Z-4.
N850 G0 X7.5
N860 G1Z0F1000
N870 G1 X=(R2+(16.*TAN(R3))*2) Z16. C1=(16./2.8)*360 F35
N500 G1 X=(R2+(17.6*TAN(R3))*2) Z17.6 C1=(17.6/2.8)*360 F35
N880 G1 X=(R2+(33.*TAN(R3))*2) Z33. C1=(33/2.8)*360 F35
N890 G1 X8.5 F1000
;2ND TIME T2
N900 G1 Z17.5 C1=(17.5/2.8)*360 F500
N910 G1 X=(R2+(18*TAN(R3))*2) Z18.15 C1=(18/2.8)*360 F35
N920 G1 X=(R2+(33.*TAN(R3))*2) Z33.45 C1=(33./2.8)*360 F35
G1 X7.5 F1000
N930 G0Z-4.
N940 G28X250.M5
N950 WCS140
N960 G28 Z0 M213
N970 MSG("")
N980 M1
N990 M133;5
N1000 MSG("TOURNAGE 60.MM")
N1010 T3131
N1020 M203
N1030 MS1
N1040 G95G0X13.Z36.0M3S2500
N1050 G1G41X6.55Z37.F0.2
N1060 G1Z61F0.02
N1070 G1X11.8
N1090 G1X12.1Z=IC(0.15)F.02
N1095 Z61.F0.07M3S2500
N1100 G0G40X13.Z=IC(1.)
N1110 G0M213
N1120 G28X250.M5
N1130 MSG("")
N1140 M1
N1150 M131;6
N1160 MSG("TOURBI. 55MM")
N1170 T3900
N1180 MS13
N1190 M4S1800
N1200 SPOS[1]=0
N1210 Z-35. M203
N1230 WCS141
N1240 G0G94Z-4.
N1250 G0 X7.5
N1260 G1Z0F500
N1270 G1 Z30.5 C1=(30.5/2.8)*360 F500
N1280 G1 X=(R2+(31.*TAN(R3))*2) Z31 C1=(31./2.8)*360 F35
N1280 G1 X=(R2+(33.*TAN(R3))*2) Z33. C1=(33./2.8)*360 F35
N1290 G1 X=(R2+(54.5*TAN(R3))*2) Z56.3 C1=(55/2.8)*360 F35
N1300 G1 X7.5 F1000
N1310 G1 Z32.9 C1=(32.5/2.8)*360 F500
N1320 G1 X=(R2+(33.*TAN(R3))*2) Z33.3 C1=(33./2.8)*360 F35
N1330 G1 X=(R2+(55.5*TAN(R3))*2) Z56.75 C1=(55/2.8)*360 F35
G1 X7.5F1000
N1310 G1 Z32.9 C1=(32.5/2.8)*360 F500
N1320 G1 X=(R2+(33.*TAN(R3))*2) Z33.55 C1=(33./2.8)*360 F35
N1330 G1 X=(R2+(57.*TAN(R3))*2) Z57.2 C1=(55/2.8)*360 F35
G1 X8.5F1000
N1340 G0Z-4.
N1350 G28X250.M5
N1360 WCS140
N1370 G28 Z0 M213
N1380 MSG("")
N1390 M1
M133;7
N1000 MSG("TOURNAGE 80.MM")
N1010 T3131
N1020 M203
N1030 MS1
N1040 G95G0X13.Z60M3S2500
N1050 G1G41X6.55Z61.F0.2
N1060 G1Z80F0.02
N1070 G1X11.8
N1090 G1X12.1Z=IC(0.15)F.02
N1095 Z81.F0.07M3S2500
N1100 G0G40X13.Z=IC(1.)
N1110 G0M213
N1120 G28X250.M5
N1130 MSG("")
N1140 M1
M131;8
N1160 MSG("TOURBI. 75MM")
N1170 T3900
N1180 MS13
N1190 M4S1800
N1200 SPOS[1]=0
N1220 G0Z-35. M203
N1230 WCS141
N1240 G0G94Z-4.
N1250 G0 X7.5
N1260 G1Z0F500
N1270 G1 Z55.9 C1=(32.5/2.8)*360 F500
N1275 G1 X=(R2+(54.5*TAN(R3))*2) Z56.3 C1=(33/2.8)*360 F35
N1290 G1 X=(R2+(76.5*TAN(R3))*2) Z78.3 C1=(55/2.8)*360 F35[/color]N1300 G1 X7.5 F1000
N1310 G1 Z55.9 C1=(32.5/2.8)*360 F500
N1320 G1 X=(R2+(55.5*TAN(R3))*2) Z56.75 C1=(33/2.8)*360 F35
N1330 G1 X=(R2+(77.5*TAN(R3))*2) Z78.75 C1=(55/2.8)*360 F35
G1 X7.5F1000
N1310 G1 Z56.9 C1=(32.5/2.8)*360 F500
N1320 G1 X=(R2+(57.*TAN(R3))*2) Z56.9 C1=(33/2.8)*360 F35
N1330 G1 X=(R2+(79.*TAN(R3))*2) Z79.2 C1=(55/2.8)*360 F35
G1 X8.5F1000
N1340 G0Z-4.
N1350 G28X250.M5
N1360 WCS140
N1370 G28 Z0 M213
N1380 MSG("")
M1
M133;9
N1000 MSG("TOURNAGE 100.MM")
N1010 T3131
N1020 M203
N1030 MS1
N1040 G95G0X13.Z80M3S2500
N1050 G1G41X6.55Z81.F0.2
N1060 G1Z98.5F0.02
N1065 G3X9.55 Z100 CR=1.5
N1070 G1X11.8
N1090 G1X12.1Z=IC(0.15)F.02
N1095 Z101.F0.07M3S2500
N1100 G0G40X13.Z=IC(1.)
N1110 G0M213
N1120 G28X250.M5
N1130 MSG("")
N1140 M1
M131;10
N1160 MSG("TOURBI. 95MM")
N1170 T3900
N1180 MS13
N1190 M4S1800
N1200 SPOS[1]=0
N1210 waitm(14,1,3)
N1220 G0Z-35. M203
N1230 WCS141
N1240 G0G94Z-4.
N1250 G0 X7.5
N1260 G1Z0F500
N1270 G1 Z70.5 C1=(30.5/2.8)*360 F500
N1280 G1 X=(R2+(71.*TAN(R3))*2) Z71 C1=(31./2.8)*360 F35
N1280 G1 X=(R2+(73.*TAN(R3))*2) Z73. C1=(33./2.8)*360 F35
N1290 G1 X=(R2+(94.5*TAN(R3))*2) Z96.3 C1=(55/2.8)*360 F35
N1300 G1 X7.5 F1000
N1310 G1 Z72.9 C1=(32.5/2.8)*360 F500
N1320 G1 X=(R2+(73.*TAN(R3))*2) Z73.3 C1=(33./2.8)*360 F35
N1330 G1 X=(R2+(95.5*TAN(R3))*2) Z96.75 C1=(55/2.8)*360 F35
G1 X7.5F1000
N1310 G1 Z72.9 C1=(32.5/2.8)*360 F500
N1320 G1 X=(R2+(73.*TAN(R3))*2) Z73.55 C1=(33./2.8)*360 F35
N1330 G1 X=(R2+(97.*TAN(R3))*2) Z97.2 C1=(55/2.8)*360 F35
G1 X8.5F1000
N1340 G0Z-4.
N1350 G28X250.M5
N1360 WCS140
N1370 G28 Z0 M213
N1380 MSG("")
M1
N1400 M133;11
N1000 MSG("TOURNAGE 100.MM")
N1010 T3131
N1020 M203
N1030 MS1
N1040 G95G0X13.Z80M3S2500
N1050 G1G41X6.55Z81.F0.2
N1060 G1Z98.5F0.02
N1065 G3X9.55 Z100 CR=1.5
N1070 G1X11.8
N1090 G1X12.1Z=IC(0.15)F.02
N1095 Z101.F0.07M3S2500
N1100 G0G40X13.Z=IC(1.)
N1110 G0M213
N1120 G28X250.M5
N1130 MSG("")
N1140 M1
N1580 G28Y0.Z0.
N1590 WAITM(99,1,2,3)
N1600 M99
N1610 M30
en rouge l alarme apparait lorque C1 depasse 57
merci de vos reponses
vive l'usinage
voila notre probleme, nous avons une decolleteuse star ecas 32t, nous realisons frequemment des tourbillonage pour des vis de longueur 25,30,40,50,60 sur des diametres de 6.5, avec comme contraintes, pas de 2.8 profondeur de fond de filet 3.6 , mais nous devons faire des vis de longueur 100 et la rien ne vas plus.
alors si vous connaisez bien le principe du tourbillonage nous sommes preneurs!!!
voici le programme
N10 CH3
N20 R2=3.65;DIAMETRE DEPART TOURBILLONNAGE Z0
N30 R3=0.45;ANGLE DE FILETAGE AU RAYON
N40 R4=95;LONGUEUR FILETAGE
N50 G0
N60 G28 X250.
N70 G28 Z0 Y0
N80 WAITM(1,1,3)
N90 TOP:
N100 G97
N110 G40 G95
N120 WCS140
N130 G28 X250.
N140 WAITM(2,1,2,3)
N150 MSG
N160 M20
N170 MSG("TOURNAGE 19.MM")
N180 T3131
N190 G0 X100.
N200 M133;1
N210 M203
N220 MS1
N230 G95G0X13.Z0M3S2500
N240 G1X-1.F0.03
N250 G1Z-1.F0.5
N260 G1G41Z-0.1X-0.1
N270 G1X0Z0F0.02
N280 G2 X1.732 Z.5 CR=1.
N290 G1X6.55 ANG=30.;3.7631
N300 G1Z19.F.02
N310 G1X11.6Z=IC(2.)
N320 G1X12.1Z=IC(0.25)F.02
N330 G0G40X13.Z=IC(1.)
N340 G0M213
N350 G28X250.M5
N360 MSG("")
N370 M1
N380 M131;2
N390 MSG("TOURBI.16MM ")
N400 T3900
N410 MS13
N420 M4S1800
N430 SPOS[1]=0
N440 waitm(10,1,3)
N450 G0Z-30. M203
N460 WCS141
N470 G0G94Z-4.
N480 G0 X=R2
N490 G1Z0F500
N500 G1 X=(R2+(18.*TAN(R3))*2) Z18. C1=(18./2.8)*360 F35
N510 G1X7.5 F1000
N520 G0Z-4.
N530 G0X100.
N540 M131;FRAISAGE
N550 G28X250.M5
N560 WCS140
N570 G28 Z0 M213
N580 MSG("")
N590 M1
N760 MSG("EBAVURAGE TOURBI. 16MM")
N770 T3900
N810 waitm(19,1,3)
N780 MS13
N790 M4S1800
N800 SPOS[1]=0
N820 G0Z-34. M203
N830 WCS141
N840 G0G94Z-4.
N850 G0 X=R2
N860 G1Z0F500
N500 G1 X=(R2+(11.*TAN(R3))*2) Z11. C1=(11./2.8)*360 F35
N500 G1 X=(R2+(18.*TAN(R3))*2) Z18.1 C1=(18./2.8)*360 F35
N890 G1 X7.5 F1000
N930 G0Z-4.
N940 G28X250.M5
N950 WCS140
N960 G28 Z0 M213
N970 MSG("")
N980 M1
N610 MSG("TOURNAGE 38.MM")
N620 T3131
G0X150.
N600 M133;3
N630 M203
N640 MS1
N650 G95G0X13.Z16.5M3S2500
N660 G1G41X6.55Z17.5F0.2
N670 G1Z38.F0.02
N680 G1X11.6Z=IC(2.)
N690 G1X12.1Z=IC(0.25)F.02
N700 G0G40X13.Z=IC(1.)
N710 G0M213
N720 G28X250.M5
N730 MSG("")
N740 M1
N750 M131;4
N760 MSG("TOURBI. 33MM")
N770 T3900
N780 MS13
N790 M4S1800
N800 SPOS[1]=0
N810 waitm(12,1,3)
N820 G0Z-34. M203
N830 WCS141
N840 G0G94Z-4.
N850 G0 X7.5
N860 G1Z0F1000
N870 G1 X=(R2+(16.*TAN(R3))*2) Z16. C1=(16./2.8)*360 F35
N500 G1 X=(R2+(17.6*TAN(R3))*2) Z17.6 C1=(17.6/2.8)*360 F35
N880 G1 X=(R2+(33.*TAN(R3))*2) Z33. C1=(33/2.8)*360 F35
N890 G1 X8.5 F1000
;2ND TIME T2
N900 G1 Z17.5 C1=(17.5/2.8)*360 F500
N910 G1 X=(R2+(18*TAN(R3))*2) Z18.15 C1=(18/2.8)*360 F35
N920 G1 X=(R2+(33.*TAN(R3))*2) Z33.45 C1=(33./2.8)*360 F35
G1 X7.5 F1000
N930 G0Z-4.
N940 G28X250.M5
N950 WCS140
N960 G28 Z0 M213
N970 MSG("")
N980 M1
N990 M133;5
N1000 MSG("TOURNAGE 60.MM")
N1010 T3131
N1020 M203
N1030 MS1
N1040 G95G0X13.Z36.0M3S2500
N1050 G1G41X6.55Z37.F0.2
N1060 G1Z61F0.02
N1070 G1X11.8
N1090 G1X12.1Z=IC(0.15)F.02
N1095 Z61.F0.07M3S2500
N1100 G0G40X13.Z=IC(1.)
N1110 G0M213
N1120 G28X250.M5
N1130 MSG("")
N1140 M1
N1150 M131;6
N1160 MSG("TOURBI. 55MM")
N1170 T3900
N1180 MS13
N1190 M4S1800
N1200 SPOS[1]=0
N1210 Z-35. M203
N1230 WCS141
N1240 G0G94Z-4.
N1250 G0 X7.5
N1260 G1Z0F500
N1270 G1 Z30.5 C1=(30.5/2.8)*360 F500
N1280 G1 X=(R2+(31.*TAN(R3))*2) Z31 C1=(31./2.8)*360 F35
N1280 G1 X=(R2+(33.*TAN(R3))*2) Z33. C1=(33./2.8)*360 F35
N1290 G1 X=(R2+(54.5*TAN(R3))*2) Z56.3 C1=(55/2.8)*360 F35
N1300 G1 X7.5 F1000
N1310 G1 Z32.9 C1=(32.5/2.8)*360 F500
N1320 G1 X=(R2+(33.*TAN(R3))*2) Z33.3 C1=(33./2.8)*360 F35
N1330 G1 X=(R2+(55.5*TAN(R3))*2) Z56.75 C1=(55/2.8)*360 F35
G1 X7.5F1000
N1310 G1 Z32.9 C1=(32.5/2.8)*360 F500
N1320 G1 X=(R2+(33.*TAN(R3))*2) Z33.55 C1=(33./2.8)*360 F35
N1330 G1 X=(R2+(57.*TAN(R3))*2) Z57.2 C1=(55/2.8)*360 F35
G1 X8.5F1000
N1340 G0Z-4.
N1350 G28X250.M5
N1360 WCS140
N1370 G28 Z0 M213
N1380 MSG("")
N1390 M1
M133;7
N1000 MSG("TOURNAGE 80.MM")
N1010 T3131
N1020 M203
N1030 MS1
N1040 G95G0X13.Z60M3S2500
N1050 G1G41X6.55Z61.F0.2
N1060 G1Z80F0.02
N1070 G1X11.8
N1090 G1X12.1Z=IC(0.15)F.02
N1095 Z81.F0.07M3S2500
N1100 G0G40X13.Z=IC(1.)
N1110 G0M213
N1120 G28X250.M5
N1130 MSG("")
N1140 M1
M131;8
N1160 MSG("TOURBI. 75MM")
N1170 T3900
N1180 MS13
N1190 M4S1800
N1200 SPOS[1]=0
N1220 G0Z-35. M203
N1230 WCS141
N1240 G0G94Z-4.
N1250 G0 X7.5
N1260 G1Z0F500
N1270 G1 Z55.9 C1=(32.5/2.8)*360 F500
N1275 G1 X=(R2+(54.5*TAN(R3))*2) Z56.3 C1=(33/2.8)*360 F35
N1290 G1 X=(R2+(76.5*TAN(R3))*2) Z78.3 C1=(55/2.8)*360 F35[/color]N1300 G1 X7.5 F1000
N1310 G1 Z55.9 C1=(32.5/2.8)*360 F500
N1320 G1 X=(R2+(55.5*TAN(R3))*2) Z56.75 C1=(33/2.8)*360 F35
N1330 G1 X=(R2+(77.5*TAN(R3))*2) Z78.75 C1=(55/2.8)*360 F35
G1 X7.5F1000
N1310 G1 Z56.9 C1=(32.5/2.8)*360 F500
N1320 G1 X=(R2+(57.*TAN(R3))*2) Z56.9 C1=(33/2.8)*360 F35
N1330 G1 X=(R2+(79.*TAN(R3))*2) Z79.2 C1=(55/2.8)*360 F35
G1 X8.5F1000
N1340 G0Z-4.
N1350 G28X250.M5
N1360 WCS140
N1370 G28 Z0 M213
N1380 MSG("")
M1
M133;9
N1000 MSG("TOURNAGE 100.MM")
N1010 T3131
N1020 M203
N1030 MS1
N1040 G95G0X13.Z80M3S2500
N1050 G1G41X6.55Z81.F0.2
N1060 G1Z98.5F0.02
N1065 G3X9.55 Z100 CR=1.5
N1070 G1X11.8
N1090 G1X12.1Z=IC(0.15)F.02
N1095 Z101.F0.07M3S2500
N1100 G0G40X13.Z=IC(1.)
N1110 G0M213
N1120 G28X250.M5
N1130 MSG("")
N1140 M1
M131;10
N1160 MSG("TOURBI. 95MM")
N1170 T3900
N1180 MS13
N1190 M4S1800
N1200 SPOS[1]=0
N1210 waitm(14,1,3)
N1220 G0Z-35. M203
N1230 WCS141
N1240 G0G94Z-4.
N1250 G0 X7.5
N1260 G1Z0F500
N1270 G1 Z70.5 C1=(30.5/2.8)*360 F500
N1280 G1 X=(R2+(71.*TAN(R3))*2) Z71 C1=(31./2.8)*360 F35
N1280 G1 X=(R2+(73.*TAN(R3))*2) Z73. C1=(33./2.8)*360 F35
N1290 G1 X=(R2+(94.5*TAN(R3))*2) Z96.3 C1=(55/2.8)*360 F35
N1300 G1 X7.5 F1000
N1310 G1 Z72.9 C1=(32.5/2.8)*360 F500
N1320 G1 X=(R2+(73.*TAN(R3))*2) Z73.3 C1=(33./2.8)*360 F35
N1330 G1 X=(R2+(95.5*TAN(R3))*2) Z96.75 C1=(55/2.8)*360 F35
G1 X7.5F1000
N1310 G1 Z72.9 C1=(32.5/2.8)*360 F500
N1320 G1 X=(R2+(73.*TAN(R3))*2) Z73.55 C1=(33./2.8)*360 F35
N1330 G1 X=(R2+(97.*TAN(R3))*2) Z97.2 C1=(55/2.8)*360 F35
G1 X8.5F1000
N1340 G0Z-4.
N1350 G28X250.M5
N1360 WCS140
N1370 G28 Z0 M213
N1380 MSG("")
M1
N1400 M133;11
N1000 MSG("TOURNAGE 100.MM")
N1010 T3131
N1020 M203
N1030 MS1
N1040 G95G0X13.Z80M3S2500
N1050 G1G41X6.55Z81.F0.2
N1060 G1Z98.5F0.02
N1065 G3X9.55 Z100 CR=1.5
N1070 G1X11.8
N1090 G1X12.1Z=IC(0.15)F.02
N1095 Z101.F0.07M3S2500
N1100 G0G40X13.Z=IC(1.)
N1110 G0M213
N1120 G28X250.M5
N1130 MSG("")
N1140 M1
N1580 G28Y0.Z0.
N1590 WAITM(99,1,2,3)
N1600 M99
N1610 M30
en rouge l alarme apparait lorque C1 depasse 57
merci de vos reponses
vive l'usinage
